A large order can be worth a second look before it goes to production. The starter rule Require a second supervisor for orders over a number of units makes the release of every order over the number of units you choose wait for a second, different Supervisor.
Use the starter rule
You need the Author role. The cards belong to one rules draft, because their blanks are that draft's own customer codes and item families and this site's enabled receiving destinations, so the draft has to be saved first. A card is offered for a draft in the rules format this page edits that has fewer than 32 rules, and a card whose blank the draft cannot fill is left out. What the card adds goes into the next draft version: order decisions already made keep the rules they were made with, and new orders keep following the active release until a Reviewer activates a new one.
- Open Mappings and routing and find the draft under Drafts and independent proof.
- Open Start from a starter rule in that draft. Under Starter rules, find Require a second supervisor for orders over a number of units, in Approval, or type a word from its title in Search starter rules and Help.
- Fill in the blanks in the card's sentence, "Orders for more than … units need a second supervisor to approve their release.":
- Units: a whole number from 1 to 100,000. It starts at 40, the number in the home page's example; it illustrates a policy and is not a default.
- Choose Use this rule. The button waits until every blank has a value.
OrderRun saves the next draft version with the rule added after the draft's other rules. Its condition is that the order's total units are more than your number, and its one action is Require a second Supervisor. Its rule ID is the card's name, with -2 or -3 added if the draft already uses it, and its explanation is the card's sentence with your values in it. It is exactly what typing the same rule into Advanced setup: complete rules and independent examples and choosing Save draft would save, and you are recorded as a contributor to that version, so a Reviewer who did not contribute to it must activate it. No AI is asked, and nothing is proved, approved or activated. The draft then says which rule was added and what to do next.
Where drafting a condition in plain English is available for your site, the card also offers Reword with AI. It adds the same rule, then opens Draft a condition in plain English on that rule, with the card's sentence in Describe the condition in plain English. Nothing is sent until you choose Prepare condition proposal yourself, and that request counts against your authoring allowance like any other. Where it is not available, which includes the sample workspace, the card offers Use this rule alone.
Where SmartFACT Automation is connected to OrderRun, you can also arrive here from New requirement there, which offers the cards of the draft saved most recently. Its Use this rule makes nothing: it opens that draft's own page with this card alone and its blanks filled in, and the page names the draft. Check the draft and the blanks, then choose Use this rule on the page. See every starter rule shows all the draft's cards. If you were signed out, signing in brings you back to the card, also after choosing an organisation.
What the rule does
The count is the whole order's units: the quantities of all its lines added up, so every line sees the same total. "More than 40" means 41 or more. When the active release has this rule, such an order is accepted and prepared for release as usual, then waits under Releases waiting for approval until a second, different Supervisor approves it; only then does its factory pack go to production. One person cannot approve twice.
In the Bracket routing rules at Brighouse works, with 40 units, a 60-unit BENCHCO order needs two Supervisors to approve its release and a 40-unit order needs one.
Run the independent examples
A starter rule writes no example. Each example's expected decision for a whole order is yours to state from your intended process, and OrderRun never works it out for you.
Choose Run independent examples on the draft. Every example whose expected decision the new rule changes fails, with its expected and actual decision side by side under Independent example results. That list is exactly the work the rule leaves you: for each one, decide from your intended process whether the rule or the example is wrong, and correct the example's expected decision in Edit this draft. Add examples the rule decides too: an order just over your number, expected to need a second approver, and one exactly at your number, expected not to. Save the draft and run the examples again until they pass. Then a Reviewer who did not contribute to the draft activates it, as mappings and routing rules describes.
Change it later
Nothing about a starter rule makes its rule permanent. In Edit this draft, change or remove it like any other rule, or use another card. Save the draft, run the examples and have it activated in the same way. Order decisions already made keep the rules they were made with.
If the card is refused
- This draft already has a rule with the same condition and actions. The draft already asks for a second Supervisor above that number of units.
- This starter rule has changed since the page was loaded. OrderRun has a newer version of the card. Reload the page and choose the card again.
- The draft changed after this page was loaded. Someone saved the draft after you opened the page. Reload it, check what changed, then use the card again.
- A blank on this card is not one of this draft's own values. The draft's mappings or the site's destinations changed under the card. Reload the page and fill it in again.
- Starter rules can only be added to a draft in the rules format this page edits, with fewer than 32 rules. Remove a rule the draft no longer needs, or start the rule in another draft.