An order on credit stop, or any order your own software marks, should not be booked until someone has checked it. The starter rule Hold an order and tell the packer why adds one Assisted rule that holds the despatch when the order source sends the mark you choose, and shows your message to the packer and the supervisor.
Use the starter rule
You need the Author role and an active order source that sends a fact with listed values or a yes-or-no fact, such as whether the order is on credit stop. The rule is added to the site's Assisted draft: stations keep following the active release until a Reviewer activates a new one.
- Open Assisted rules. The Starter rules cards come before the draft.
- Find Hold an order and tell the packer why. It is under Hold a despatch; you can also type a word from its title in the search box, which finds Help articles too.
- Fill in the blanks in the card's sentence, "Hold the despatch when …, and tell the packer: …":
- Mark on the order: one value of a fact your order source sends, such as “on credit stop is true”. Facts with listed values and yes-or-no facts are offered.
- Message for the packer: up to 200 characters, without < or >. The card starts with “Check with accounts before packing this order.”
- Choose Use this rule. The button waits until every blank has a value.
The rule is added to the draft as its next revision, exactly as if you had typed it into the draft yourself, and the page lists it under the draft. No AI is asked.
Where describing a rule in plain English is available on this site, the card also offers Reword with AI. It adds the same rule, then opens Describe when a rule applies on it with the card's sentence, for you to change and send. It is never offered in the sample workspace.
What the rule does
The rule belongs to the decision which preset an Assisted or Automatic station recommends, or whether it holds the despatch. When an order with the mark loads at an Assisted or Automatic station, the packer sees the hold and your message, and nothing books for it in any mode: a hold wins over every recommendation. Once your software no longer marks the order, the next scan at an Assisted station clears the hold; before that, a supervisor can record an exception in Shipments to book it by hand. Automatic never books past a hold.
The hold's reason code is made from the fact the rule tests, such as on_credit_stop, and is shown with the hold.
Check the examples
Under Examples prepared for the rule's title, ParcelOffice offers examples made from one of this site's own example orders, with only the facts the rule reads changed: one the rule applies to and, for each part of its condition, one it does not. Each suggests an outcome: “held” with the hold's reason code for the order it applies to, and “no rule applies” for the others. Choose Check it in the example form, read the order and the expected outcome, change anything that does not suit your site, then choose Add example. Nothing is added until you do.
Check each suggestion against the draft's other rules, because another rule may also apply to the same order. When the site has no example order yet, write the examples in the form yourself: every rule needs one example it applies to and one it does not.
Release it
Choose Verify and create a candidate. Every example is run against the whole draft. A difference names the example: decide whether the rule or the example is wrong before changing either. A Reviewer then activates the proven release with their authenticator from the last hour, and turns Assisted on for the bench on Site settings if it is not on already; see rule review. Automatic uses the same release only once a Reviewer has qualified it.
If the card is refused
The page says what stopped it, and nothing was added:
- “Not done: that starter rule card has changed, or this site no longer has what it named. Reload and choose it again.” Reload the page and fill in the card again.
- “Not done: the draft already has that rule, so nothing changed.”
- “Not done: someone saved a newer draft. Reload, then reapply your change.” Reload, then use the card again.
- “Not done: write the message for the packer in up to 200 characters, without < or >.” Shorten the message, or take out the < or >, and use the card again.
A card chosen in SmartFACT Automation
Where SmartFACT Automation is connected to ParcelOffice, you can also choose a starter rule there. It opens here on its own card, with its blanks filled in, under the note “You chose Hold an order and tell the packer why in SmartFACT Automation. Check its blanks, then use the rule here.” Nothing is made until you choose Use this rule on this page. Show all starter rules shows every card again.
If the card has changed since it was chosen, the page says “The card you chose in SmartFACT Automation has changed, or this site no longer has what it named. Choose it again below.”
Changing or removing it later
The rule is an ordinary rule of the draft. To change or remove it, edit or delete it in the draft, retire the examples that expect it, verify the draft and have it activated as usual. Nothing about a starter rule makes its rule permanent, and changing a starter rule later changes no rule already made from it.