Skip to content
SmartFACT HelpHandbooksWatch and practise
Handbooks: LabelRules

A printer stopped printing

Read the printer's state on Printer setup, then check the workstation, the printer and the PrintStation app in the order the page gives.

Review edition · 13 November 2026 · For Owner, Supervisor

On this page

When labels stop coming out, the question is always the same: is it the workstation, the PrintStation app, the printer or the network? Printer setup answers it from PrintStation's own record of the printer your site's labels go to. A Supervisor or the Owner can read it. It only reads: nothing on it changes a printer, a job or a record.

This page is for a site that prints unattended to a PrintStation destination. If your site prints from the PrintStation panel, read when the page has nothing to show.

Read the printer's state

  1. Open Printer setup. Printer state is the first box on the page.
  2. Read the state under the printer's name. It is Working or Attention needed, with the reason in a sentence underneath.
  3. Under Check next, follow the checks in the order given. Each has a Help link to its section below.
  4. After each thing you put right, press Read again. The page never reads again by itself.

A reading is trusted for 90 seconds. After that the box says the reading is more than 90 seconds old; press Read again before relying on it.

LabelRules has one printer for a site, so there is no list of stations here and no quiet state. The state describes the printer only.

What the facts mean

  • Printer is the printer's own name on its workstation.
  • Last copy sent is the moment the PrintStation app accepted a copy for that printer. Sent means the app accepted the copy. It does not show that paper came out, because PrintStation cannot know that. A recent time with no labels in the tray points at the printer itself.
  • Recent failures are the copies PrintStation recorded as not sent or uncertain in the last seven days, newest first, each with PrintStation's reason. A copy that was not sent is tried again, so a failure older than Last copy sent has been overcome. Only a failure since the last copy sent makes the state Attention needed; where nothing has been sent yet, any listed failure does.
  • Copies waiting counts LabelRules' own copies queued for the printer.
  • App last heard from is when PrintStation last heard from its app on the workstation. PrintStation treats the app as offline once it has heard nothing from it for 90 seconds.
  • PrintStation app is the version the app last reported. Give it to support if you ask for help.

Last copy sent and Recent failures count every SmartFACT product's copies on that printer, and PrintStation's own calibration copies, not only LabelRules' labels. So a failure listed here may belong to another product's job.

Follow the reason the page gives

  • PrintStation has not heard from its app on the workstation that serves this printer. Start with power and network at the workstation, then the PrintStation app.
  • A copy was not sent to the printer, with PrintStation's reason. Where the reason is that the app could not find the printer, start with the printer's own display and its cable. Where printing was paused in the app, or the app was closing, start with the PrintStation app. A copy that was not sent is tried again while its delivery window lasts, so read again after putting the cause right.
  • It is not known whether a copy reached the printer, or PrintStation is holding this printer. Stop. No more copies go to the printer until someone records in PrintStation what happened to the uncertain copy. Follow uncertain output. Do not move the site to another printer to get round the hold.
  • The printer is not ready. The app is paused or cannot see the printer, or the printer's set-up in PrintStation is not finished. Check the printer's own display and the PrintStation app, then ask the PrintStation Owner.
  • This printer is switched off in PrintStation. Nothing on the floor puts that right. The PrintStation Owner switches the destination back on. Read PrintStation destinations.
  • PrintStation no longer lists this printer for LabelRules. The destination was removed in PrintStation, or LabelRules is no longer allowed to use it. The LabelRules Owner chooses a destination again under Print through PrintStation on the same page. A new route needs a new qualification label: read printer set-up.
  • The printer's state is not known. LabelRules could not reach PrintStation, or got no answer it could use, and the page says which above the printer's name. Nothing shown is an earlier reading. Press Read again in a moment before checking anything on the floor.

Power and network at the workstation

The workstation is the computer beside the printer that runs the PrintStation app.

  1. Check that it is switched on and awake, with someone signed in to its desktop. A computer that has gone to sleep or shows a sign-in screen is not running the app.
  2. Check that it is on the network: open any web page on it.
  3. Wait a minute, then press Read again in LabelRules. App last heard from should show a time within the last minute.

If the workstation is on the network and the app is still not heard from, go on to the PrintStation app.

The printer's own display

Look at the printer itself before changing anything in software.

  1. Check that it has power and is switched on.
  2. Check that the right label stock is loaded and the lid or head is closed.
  3. Read its display or lights for an error or a pause, and clear it as the printer's own guide says.
  4. Check the cable or network connection between the printer and the workstation.

Then press Read again. The suite's printer pages cover the settings PrintStation needs: Zebra printers and Brother QL printers.

Labels that came out while the page was showing a fault still count. Collect them and tell the Supervisor before anyone prints the same copies again.

The PrintStation app

On the workstation, find the PrintStation app's icon in the Mac menu bar or the Windows system tray.

  1. If the icon is missing, the app is not running. Start it. It also starts when someone signs in to the computer.
  2. Open its menu and check that the app is paired with PrintStation and that printing is not paused.
  3. Press Read again in LabelRules.

Pairing, approving and configuring the app belong to the PrintStation Owner: read PrintStation's agent set-up. If the app has to be installed again, read installing the PrintStation app. A restart or a new installation does not settle an uncertain copy from before it.

When the page has nothing to show

  • This site's labels print from the PrintStation panel. No one printer serves the site, so there is no printer state to show. Check the workstation you are printing from, and read attended printing in PrintStation.
  • This site's labels do not go through PrintStation. PrintStation has no printer to report on for this site. Read printer set-up.
  • LabelRules could not reach PrintStation just now. Read again in a moment. If it stays the same, PrintStation itself may be unavailable; tell the Owner.
  • LabelRules is not allowed to print to this organisation's printers. A PrintStation Owner allows it under Products in PrintStation. Read allowed products.
  • You cannot see Printer state at all. It is shown to a Supervisor and the Owner. Ask one of them to read it.

What this page does not do

It does not print, retry, cancel or reprint anything, and it does not control a printer or a workstation. It sends no email or alert: someone has to open it. It does not settle a copy whose outcome is uncertain; that is recorded in PrintStation.

When you hand the problem on, copy the state, the reason, the facts and the time after Read exactly as the box shows them. They name no person and no job, so they can go to support as they stand.