This page covers Zebra's ZD421 and ZD621 desktop label printers, printing labels from SmartFACT products through PrintStation. It names the printer settings that decide whether a label is the right size, in the right place and readable, each as Zebra names it, and uses PrintStation's qualification as the test.
It was written from Zebra's ZD421 and ZD621 Desktop Printer User Guide, which says it was last published on 2 September 2026, read on 10 November 2026. That guide covers the ZD421 and ZD621 in their direct thermal and thermal transfer versions, the ZD421 ribbon cartridge printer and the ZD621R. This page has not been checked on a printer, and it makes no claim about any other Zebra model. The guide names no setting of the Windows printer driver, so this page names none either.
How a label reaches the printer
PrintStation sends each label under a media profile, chosen when the printer is set up in PrintStation:
| PrintStation media profile | What is sent |
|---|---|
| 100 × 150 mm label, 203 DPI or 300 DPI | A picture of the label at exactly that size, through the printer's driver on the workstation |
| 4 × 6 inch label, 203 DPI or 300 DPI | The same, at 101.6 × 152.4 mm |
| 100 × 150 mm label, 203 DPI, ZPL | The label in Zebra's own printer language, unchanged |
Choose the profile whose DPI is the printhead's. Zebra's guide says the model and resolution are listed on the printer's configuration report.
PrintStation changes no setting on the printer. Darkness, speed, media type and sensing are the printer's own, set at the printer or in its driver.
Read what the printer is set to
With labels loaded and the printer ready, press and hold FEED and CANCEL together for two seconds. The printer prints its configuration report. The lines that matter here are DARKNESS, PRINT SPEED, MEDIA TYPE, SENSOR SELECT, PRINT METHOD, PRINT WIDTH and LABEL LENGTH.
On a ZD621 with a colour touch display the same settings are under Print, then Print Quality. On the printer's own web page they are under View and Modify Printer Settings.
Print the report before you change anything and again afterwards, and keep both with the qualification.
Media and ribbon type
Zebra's guide gives a scratch test for a roll of labels. Scratch the print surface firmly and quickly with a fingernail. If a black mark appears, the labels are direct thermal and need no ribbon. If none appears, they are thermal transfer and need a ribbon.
Set Print Type to match: Direct Thermal or Thermal Transfer. The configuration report shows it as PRINT METHOD.
For thermal transfer, Zebra's guide says:
- use a ribbon wider than the labels and their backing, to protect the printhead;
- match the ribbon to the labels. Its ribbons are wax, wax and resin, and resin;
- load no ribbon when printing on direct thermal labels.
Gap sensing
Label Type tells the printer how one label is told from the next:
| Zebra's value | For |
|---|---|
| Gap/Notch | Labels on a backing with a gap between them. This is the default. |
| Mark | Media with a black mark on the back |
| Continuous | Media with no gap or mark. The label's length then comes from the software. |
The configuration report shows it as MEDIA TYPE.
After loading labels of a new kind, run a SmartCal Media Calibration: with the printer ready, press and hold PAUSE and CANCEL together for two seconds. The printer feeds and measures a few labels and sets its sensing. Zebra says this need not be repeated for a new roll of the same labels: press FEED once or twice to line the roll up.
Two more settings belong to sensing, and usually need no change:
- Sensor Type is TRANSMISSIVE for gaps and REFLECTIVE for black marks and notches.
- The movable sensor's default position suits most labels with gaps.
If SmartCal does not find the labels, Zebra's guide has a Manual Calibration, started by holding PAUSE, FEED and CANCEL together for two seconds. Leave Label Sensor alone: the guide says not to change it unless Zebra's support tells you to.
Label size
Label Length is measured by calibration. Zebra's guide says the value cannot be changed there.
Label Width (Dots) is the printing width, shown as PRINT WIDTH on the report. Zebra's guide says its default is the printer's maximum width, and for the ZD621 gives up to 832 dots at 203 dpi. Zebra says that too narrow a setting leaves part of the label unprinted, and too wide a setting can print beyond the label's edges. At 203 dpi a dot is 0.125 mm, so a label 100 mm wide is 800 dots.
For a ZPL media profile, PrintStation asks for the printer's print width in dots when the printer is set up, and offers 832. Enter the printer's own figure if it differs.
For the other label profiles, the label size is also set in the printer's driver on the workstation. Set it to the size of the labels loaded, and turn off anything that shrinks or enlarges a page to fit.
Darkness
Zebra's advice is to set Darkness to the lowest setting that gives good print quality. Its values run from 0.0 to 30.0, and the report's default is 10.0. Zebra says that too high a setting can make the image unclear, stop barcodes scanning, burn through the ribbon and wear the printhead early.
To find the setting, Zebra's guide has a print quality report, printed with the FEED self test, and a Manual Print Darkness Adjustment that prints a pattern at each darkness in turn.
Print Speed
Zebra says that slower speeds typically give better print quality. For the ZD621 its guide gives 2 to 8 inches per second at 203 dpi and 2 to 6 at 300 dpi. The topic gives no range for the ZD421: read PRINT SPEED on its configuration report.
Do not set a speed above the maximum the maker of the labels or ribbon gives for them.
A ZPL label can carry its own settings
A label sent in Zebra's printer language can set darkness, speed, media type and print method for itself, and a carrier's label may do so. PrintStation accepts those commands inside a label and refuses any command that changes or reports the printer's configuration. So qualify a ZPL profile with the stock the labels will really use, and expect a carrier's label to print as the carrier set it.
The test: PrintStation qualification
Settings are right when the calibration copy passes. In PrintStation, an Owner opens the printer and follows Qualify a printer and media profile: print the calibration copy, measure between its reference marks, scan its barcode and record what came out.
| PrintStation's check | If it fails, look at |
|---|---|
| Each measurement within 0.5 mm of the expected value | The label size in the driver, anything that scales the page, and whether the profile's DPI is the printhead's |
| Scan the barcode into this field | Darkness, Print Speed, and whether the ribbon suits the labels |
| Exactly one copy came out | Label Type and the SmartCal calibration: a blank label after each print points to sensing |
| It is upright, with TOP at the top | The page orientation in the driver |
| Nothing is clipped at any edge | Label Width (Dots), the label size in the driver, and how the roll is loaded |
| It was not shrunk or enlarged to fit | Anything in the driver that fits the page to the label |
At Hartwell & Pryce Engineering's Brighouse works, Sarah Hughes qualifies the despatch bench printer for 100 × 150 mm labels at 203 DPI. The scratch test leaves a black mark, so the labels are direct thermal and she loads no ribbon. She runs SmartCal, prints the configuration report and reads DARKNESS 10.0, MEDIA TYPE GAP/NOTCH and PRINT METHOD DIRECT-THERMAL. In PrintStation she prints the calibration copy and measures 50.1 mm across and 50.0 mm down, against 50.05 mm expected. The barcode scans. One copy came out, upright, with nothing clipped or scaled, so she chooses Record and qualify.
Those figures describe one printer and one roll. They are not settings to copy. Enter what you measure, including a failure: do not enter the expected value because it is the target.
A qualification belongs to one workstation, one printer and one media profile. After changing the printer, its driver, the labels or the ribbon, check it again. LabelRules also records a qualification of its own label on the same printer: see LabelRules printer set-up.