When no offcut in the rack fits a job, Find a piece can take a new length from StoresFlow for that job, where your site has StoresFlow and its Owner has connected the two. Stores reserve, pick and issue the length in StoresFlow. It then arrives here as a record to measure, label and put away in a rack, as every piece is, and it is reserved for the job when you put it away.
No request is sent to StoresFlow until an Owner has switched the link on in RemnantRack (see Connect StoresFlow for new stock) and StoresFlow's Owner has connected RemnantRack and mapped the material there. Until then Find a piece says nothing about StoresFlow.
When Take new stock is offered
Search as usual: describe the whole job in Find a piece and choose Search. Under the result, Take new stock from StoresFlow appears only when all of these are true:
- SmartFACT Accounts confirms that your organisation has StoresFlow. While it cannot say, nothing about StoresFlow is shown, and requests already made are still sent.
- StoresFlow has mapped this material to one of its items, with the length of one stock bar.
- One stock bar is at least as long as the job needs, with every allowance counted.
- The job does not need an exact batch. A request to StoresFlow cannot promise a lot, so a job that needs one is not offered new stock.
The panel says what you will get: the StoresFlow item and the length StoresFlow records for one bar. If one bar is too short, or the job needs a batch, the result says so instead.
If pieces in the rack fit, use one of them. Take new stock is still shown, but its button works only after you tick I decline the pieces that fit, and take new stock instead. Declining is recorded with the request.
Ask, and follow the request
Choose Take new stock. One request goes to StoresFlow for one bar, for this job. It is sent after RemnantRack has recorded it; if StoresFlow cannot be reached, the same request is sent again later, never a second one. If the answer is lost, choose Check again: it sends the same request and records nothing more. Do not choose Take new stock again: a new press is a new request for another bar. If you have left the page, look under My new-stock asks first.
My new-stock asks, below your reservations, shows where each request stands:
- Asked StoresFlow, not yet confirmed: it is waiting to reach StoresFlow.
- In StoresFlow: StoresFlow has it and stores are working on it.
- Issued: measure and register it: the bar has left the stockroom for you.
- Stopped: a connection problem the site Owner can see on the StoresFlow page.
- Ended: with the reason, for example StoresFlow closed it short because the item was not in stock, or it was taken back.
Take back a request you no longer need
While a request is waiting, in StoresFlow or stopped, you can take back your own request under My new-stock asks. Enter why it is no longer needed, in 10 to 500 characters, and choose Take back. StoresFlow is told and cancels it. If StoresFlow cannot be reached, the request ends here straight away and StoresFlow is told when it answers. If stores already have the bar in hand, it stays in StoresFlow: they issue it or put it back on the shelf first, and you are told so. If it still shows In StoresFlow later, you can choose Take back again. If stores issue it after all, it still comes to you, held for no job: your request shows that it was issued anyway, and the bar is registered and put away as an ordinary piece, not reserved.
A supervisor can take back someone else's request, under Other people's new-stock asks on Supervision, with a reason and a recent second-factor check. You then see under My new-stock asks that a supervisor took it back, with their name and the reason.
When the bar arrives
At a station, choose Register and, under Imported opening piece or new stock from StoresFlow, if this is one, pick the record listed as From StoresFlow, with its material, item, length and job (no job, if its request was taken back). The length shown is what StoresFlow records for one bar, not a measurement: check the material, measure the bar and record its condition. If you scan another material, the station names the material StoresFlow issued the bar as: find that bar, or, if stores sent another material, tell them, so that StoresFlow's stock is put right, and register what you have as a new piece. What you enter is what is recorded. StoresFlow's lot stays the piece's batch and cannot be changed here.
Put it away in a rack by scanning its new label and the bin, as for any piece. In the same step it is reserved for the job that asked, for the person who asked, and appears under their My reservations, for the release's usual reservation time. If it no longer fits the job (it measured shorter than StoresFlow said, for example), it is put away as an ordinary available piece and nothing is reserved. If the keep decision does not keep the bar (one registered as damaged goes to quarantine, for example), it is not kept for the job.
When the bar is cut, the remainder is registered as usual. It keeps the batch, and its history leads back to the bar StoresFlow issued, so the remainder can be traced to the issued length and its lot.