Skip to content
SmartFACT HelpHandbooksWatch and practise
Handbooks: RemnantRack

Connect StoresFlow for new stock

Switch new-stock requests on, read StoresFlow's mapping of your materials and see what needs a person.

Review edition · 13 November 2026 · For Owner

On this page

If your organisation also has StoresFlow, its stock record, RemnantRack can ask it for a new length when no offcut fits a job. As the Owner you switch this on in RemnantRack; StoresFlow's Owner connects RemnantRack there and says which StoresFlow item each material is, with the length of one stock bar. Nothing is sent to StoresFlow until you switch it on, and nothing new while SmartFACT Accounts does not confirm that your organisation has both products. From then RemnantRack sends its list of materials, and no new-stock request can be made until StoresFlow's Owner has done their part. How people then ask is in Take new stock from StoresFlow.

Open the StoresFlow page

Open StoresFlow under Site. It is for the Owner of the real site, never the sample. The page shows one of four things:

  • If your organisation does not have StoresFlow, one sentence about what it adds, with a link to its page.
  • If StoresFlow's address and keys are not set up on this installation, Not available on this installation. Nothing is sent.
  • If SmartFACT Accounts has not confirmed that your organisation has StoresFlow, a note saying so: try again in a moment. Until it confirms, no new stock is offered at Find a piece and RemnantRack sends StoresFlow nothing about your materials, even with requests switched on, so Materials in StoresFlow shows StoresFlow's last answer. Requests already recorded are still sent.
  • When Accounts confirms that your organisation has both products, the switch below.

Switch new-stock requests on or off

Under Send new-stock requests to StoresFlow, enter a reason of 10 to 500 characters and choose Send requests (or Stop sending). A second factor from the last five minutes is needed; SmartFACT Accounts asks for it if yours is older. Each change is kept in the History list with your name, the reason and how many requests were in StoresFlow at that moment.

Switching on checks with SmartFACT Accounts that your organisation has both products. The switch, Stop sending included, is shown only while Accounts confirms that, and only then is new stock offered at Find a piece. Switching off stops new requests at once. A request already recorded is still sent, even if it has not reached StoresFlow yet, and requests in StoresFlow finish there and still report back. To stop one that is not yet issued, the person who asked takes it back on Find a piece.

There is no choice of paper. RemnantRack prints nothing for stores: StoresFlow prints its own pick document, on the printer its Owner chose. If none is chosen, the page says so and stores print it in StoresFlow by hand.

Map the materials in StoresFlow

RemnantRack tells StoresFlow which materials it uses: each active material's code and description, in the unit length (one whole bar). It does this when you switch on and, while requests are switched on, whenever you open this page, every 15 minutes, and after StoresFlow refuses a request because its material is not mapped, needs review or is no longer active. It does none of this while SmartFACT Accounts does not confirm that your organisation has both products: the list stays as StoresFlow last answered. StoresFlow's Owner then maps each material to a StoresFlow item and enters the length of one bar, in StoresFlow. The StoresFlow item must be held in whole bars with the unit length, or StoresFlow refuses the mapping.

While requests are switched on, Materials in StoresFlow lists what StoresFlow last said about each material: Mapped to, with its item and one bar's length; Not mapped; or Needs review in StoresFlow. Only mapped materials are offered new stock. The page also shows whether StoresFlow has the link connected, paused or disconnected, and from which stockroom it draws. If StoresFlow did not answer, the page says so and keeps the last list.

What needs a person

Needs a person appears when something is stuck:

  • Requests that stopped before StoresFlow took them, by material, with StoresFlow's reason. A signature StoresFlow did not accept usually means the key registered in StoresFlow is not RemnantRack's current one. A request StoresFlow called malformed is a defect: tell SmartFACT support.
  • Results StoresFlow sent that RemnantRack could not apply, kept exactly as StoresFlow recorded them.

The same counts appear on Health. The page never shows pieces, jobs or who asked: that is the work of operators and supervisors, under Find a piece.