Sometimes a newly approved supplier needs one more check, and nothing else. The starter rule Add a check for a supplier status adds one approved check for units from suppliers with the status you choose, without asking for a Supervisor's release.
Use the starter rule
You need the Author role. The cards belong to one plan, because their blanks are that plan's own declared context values and approved checks, so the plan needs a saved draft first. What the card adds goes into the next draft revision: inspections already started keep the plan they started with, and new units keep following the active release until a Reviewer activates a new one.
- Open Plans and releases and find the plan.
- Open Start from a starter rule in that plan. It is already open where the site has only one plan. Under Starter rules, find Add a check for a supplier status, in Suppliers, or type a word from its title in Search starter rules and Help.
- Fill in the blanks in the card's sentence, "For units from … supplier, also include ….":
- Supplier status: a newly approved or an approved supplier, from the plan's declared supplier statuses. It starts at a newly approved.
- Approved check: one of the plan's approved checks, shown with its revision.
- Choose Use this rule. The button waits until every blank has a value.
CheckStation saves the next draft revision with the rule added under 4. Additional requirements: its Rule ID is the card's name and its explanation is the card's sentence. It is exactly what typing the same rule in Edit draft and choosing Save draft would save, and you are recorded as the author of that draft, so another Reviewer must approve it. No AI is asked, and nothing is proved, approved or activated. The plan then says what was added and what to do next.
Where describing a rule condition in plain English is available for your site, the card also offers Reword with AI. It adds the same rule, then opens Describe a rule condition on that rule with the card's sentence in When should the fixed requirement apply?. Nothing is sent until you choose Propose condition yourself, and that request counts against your authoring allowance like any other. Where it is not available, which includes the sample workspace, the card offers Use this rule alone.
Where SmartFACT Automation is connected to CheckStation, you can also arrive here from New requirement there, which offers the cards of the plan whose draft was saved most recently. Its Use this rule makes nothing: it opens that plan's page with this card alone and its blanks filled in, and the page names the plan. Check the plan and the blanks, then choose Use this rule on the page. See every starter rule shows all the plan's cards. If you were signed out, signing in brings you back to the card, also after choosing an organisation.
What the rule does
At selection, a unit whose supplier status is the one you chose gets the approved check as well as its binding's base checks. Its release is decided as before: a binding or another rule may still require a Supervisor. A unit with no supplier status cannot start inspection.
In the Bracket assembly BR-200 final inspection plan, "For units from a newly approved supplier, also include Bracket width (width-v1)." adds the width check. That plan's own rule for newly approved suppliers also requires a release, so the two rules together still ask for one.
Prove the draft
A starter rule writes no proof example. Each example's expected checks, evidence and supervisor release are yours to state from the approved method, and CheckStation never works them out for you.
Open Review frozen draft and proof and choose Run proof examples. Every example whose unit the new rule now matches fails, with its expected and actual selection side by side. That list is exactly the work the rule leaves you: for each one, decide from the approved method whether the rule or the example is wrong. Correct the example's expectation under 5. Proof examples in Edit draft, save the draft and run the proof again until it passes. Then a Reviewer who has not saved a draft of this plan reviews and activates it, as proof and approval describes.
Change it later
Nothing about a starter rule makes its rule permanent. In Edit draft, under 4. Additional requirements, change or remove it like any other, or use another card. Save the draft, prove it and have it reviewed in the same way. Inspections already started keep the plan they started with.
If the card is refused
- This draft already has a rule that does exactly this. The draft already adds that check for that supplier status, without a release.
- This starter rule has changed since the page was loaded. CheckStation has a newer version of the card. Refresh the page and fill it in again.
- The record changed after this page was loaded. Someone saved the draft after you opened the page. Refresh it, check what changed, then use the card again.
- A blank on the card is not one of this plan's values or approved checks. The plan changed under the card. Refresh the page and fill it in again.