# Set up a Datalogic scanner for the scan field

Gryphon 4500: USB keyboard, Country Mode, Global Suffix and the GS1-128 AIM ID that leaves your own codes unchanged.

Source: https://help.smartfact.ai/manuals/hardware/datalogic-scanners

Review edition: 10 November 2026

Roles: owner, supervisor

This page covers Datalogic's Gryphon 4500 handheld scanners, the corded GD4500 and the cordless GBT4500 and GM4500, used as a keyboard with a SmartFACT scan field. Each setting is named as Datalogic names it. Read [the general scanner page](/manuals/hardware/scanner-setup) first for what the scan field expects.

It was written from one document: Datalogic's [Gryphon I GD/GBT/GM4500 Product Reference Guide](https://cdn.datalogic.com/Download?iddwnfile=30026), number 800000090 (Rev C), dated May 2026, read on 10 November 2026. Page numbers below are that guide's own. This page has not been checked on a scanner, and it makes no claim about any other Datalogic model.

## How settings are made

Datalogic's guide prints a programming barcode for each setting. Scan **ENTER/EXIT PROGRAMMING MODE**, scan the settings you want, then scan **ENTER/EXIT PROGRAMMING MODE** again to accept them. This page gives the names to look for; the barcodes are in Datalogic's guide.

The guide also names **Datalogic Aladdin**, which it describes as a multi-platform utility program for configuring the reader. This page gives no Aladdin steps.

## Make it a USB keyboard

On page 29, scan **Select USB Standard Keyboard**. Datalogic describes it as USB Keyboard with standard key encoding.

The guide also has **Select USB Alternative Keyboard**, with alternative key encoding. Leave it alone unless Datalogic's support advises it: the guide says the Country Mode setting is ignored when the interface uses alternate key encoding.

A cordless scanner links to its base when it is put into it, and the guide says to do that before choosing the interface. To link a GBT4500 straight to a tablet or handheld over Bluetooth, the guide's procedure on page 24 is **Link Reader as HID device to a Bluetooth host**, with the barcode **Link to Host in HID mode**. The other procedure there, for the serial profile, gives a link that types nothing into a browser.

## Country Mode

**Country Mode** sets the country or language of the keyboard. The default is **U.S. Keyboard**. Under **Setting Country Mode**, from page 52, scan the entry that matches the keyboard of the station's computer.

## Suffix and prefix

**Global Prefix/Suffix**, on page 84, has these defaults:

| Datalogic's setting and default | For the scan field |
| --- | --- |
| Global Prefix: No Global Prefix | Leave it |
| Global Suffix: 0x0D (CR) | Leave it: a carriage return is the Enter key |
| Label ID Control: Disable | Leave it |

A scanner with Datalogic's defaults already ends each scan with Enter. Use **Set Global Suffix** only for a station that is set to Tab, and enter the tab character, hexadecimal 09, in place of 0D.

## The identifier for GS1 labels

To have LotTrail recognise a supplier's GS1 label, the scanner must send the label's identifier in front of it. Datalogic has two settings on page 86, both **Disable** by default:

| Datalogic's setting | What it does |
| --- | --- |
| GS1-128 AIM ID | Adds the identifier to GS1-128 labels only. The guide gives it as `]C1`, `]C2`. |
| Global AIM ID | Adds an AIM identifier to every kind of code. |

Set **GS1-128 AIM ID** to **Enable** and leave **Global AIM ID** at **Disable**. The guide says the two can be set independently in that way. Your own codes then arrive unchanged, and only a GS1-128 label gains the three characters LotTrail looks for.

Do not enable Global AIM ID on a station's scanner. Every code would gain three characters at the front and stop matching in every other scan field.

For GS1 DataMatrix and other kinds of code, the guide says their AIM identifiers can also be enabled one by one, and to contact Datalogic's customer support for that. It prints no barcode for them.

## The separator inside a GS1 label

**Keyboard Send Control Characters**, on page 75, is **Send Ctrl+Key** by default. Datalogic says that characters 00 to 1F hexadecimal are then sent as Ctrl and a key. The GS1 separator is 1D, so it arrives as a key press, which leaves no character in a browser field. That is why LotTrail reads a label with no separator in it, such as an item number followed by a lot, and keeps any other label as typed text.

Leave the setting at its default. Its other choices, **Send Ctrl+Shift+Key** and **Send Special Function Key**, send different keys and no character.

## If characters go missing

Two settings in the guide slow the scanner's typing. **USB Keyboard Speed**, on page 78, is the USB poll rate for a USB keyboard and is 1ms by default; the guide offers slower values. **Intercharacter Delay**, on page 77, adds a pause between characters, from 0 to 990 milliseconds in steps of 10, and is no delay by default. Change one at a time and repeat the check below after each change.

## Check it with ScannerBench

1. On the station's own computer, tablet or handheld, in the browser the station uses, open [ScannerBench](https://scannerbench.smartfact.ai/app/).
2. Choose **Start capture** and scan a label whose exact text you know.
3. The capture should end by itself, by the Enter key. Go on to **Inspect and compare**, enter the label's text as **Expected text** and look for an exact match.

What each result means on this scanner:

| ScannerBench shows | Look at |
| --- | --- |
| Nothing arrives | Select USB Standard Keyboard, or for Bluetooth, Link to Host in HID mode |
| The text arrives and the capture does not end | Global Suffix |
| Changed punctuation | Country Mode, and whether the alternative keyboard was selected |
| Extra characters at the front of every code | Global Prefix, Global AIM ID and Label ID Control |
| Characters missing from a long code | Intercharacter Delay and USB Keyboard Speed |

With GS1-128 AIM ID enabled, scan one of your own labels and one supplier's GS1-128 label. Your own should arrive exactly as printed. The supplier's should begin `]C1`.

A match shows what this scanner sent to this browser on this day. It is not a certificate for the scanner. Finish with the product's own scanner check at the station and one real scan.
