# Brother QL label printer settings for PrintStation

QL-1100 and QL-1110NWB: the DK Roll, the Quality option, label size and cutting, tested by PrintStation's qualification.

Source: https://help.smartfact.ai/manuals/hardware/brother-ql-printer-settings

Review edition: 10 November 2026

Roles: owner, supervisor

This page covers two Brother label printers, the QL-1100 and the QL-1110NWB, printing labels from SmartFACT products through PrintStation. It says which of the usual label printer settings these printers have, which they do not, and what Brother names them, and uses PrintStation's qualification as the test.

It was written from Brother's own User's Guides: the [QL-1110NWB User's Guide](https://download.brother.com/welcome/docp100364/ql-1110nwb_uke_ug_03.pdf), Version 03, and the [QL-1100 User's Guide](https://download.brother.com/welcome/docp100363/ql-1100_uke_ug_02.pdf), Version 02, read on 10 November 2026. Neither guide prints a date; Brother's site dates the files 13 March 2020 and 28 August 2019. This page has not been checked on a printer, and it makes no claim about any other QL model.

## What these printers are

Brother's specifications for both give:

| Brother's specification | What it means for PrintStation |
| --- | --- |
| Method: Direct thermal printing via thermal head | There is no ribbon and no ribbon setting |
| Print head: 300 dpi / 1296 dots | Choose a 300 DPI media profile |
| Maximum printing capability (width): 101.6 mm | A 4 × 6 inch label uses the whole width |
| Printing speed: Max. 110 mm/s | Brother adds that actual speed varies |

PrintStation's label profiles at this resolution are **4 × 6 inch label, 300 DPI** and **100 × 150 mm label, 300 DPI**. Choose the one that matches the roll loaded.

PrintStation changes no setting on the printer. What follows is set in Brother's printer driver on the workstation or in Brother's Printer Setting Tool.

## Media: the DK Roll

These printers print on Brother's DK Rolls, which Brother says use thermal paper and thermal film. The print fades in sunlight and heat, and Brother says not to use DK Rolls outdoors where durability is needed.

The guides name these roll faults, shown by the Status LED: **Roll end error**, **No media error**, **Wrong media error** and **Feed error**. For any DK Roll error, Brother's checks are:

- you are using the correct DK Roll;
- there are enough labels remaining;
- the DK Roll is installed correctly.

Neither guide lists DK Roll part numbers or sizes, so this page names no roll. The roll must be the size of the PrintStation media profile and of the label size chosen in the driver.

## Darkness

Neither guide has a darkness or density setting, in the driver or in the Printer Setting Tool. There is nothing to set.

What Brother gives for a barcode that will not scan, under "Printed barcodes cannot be read", is:

- print with the **Quality** option set to **Give priority to print quality**. On Windows it is in the printer's **Printing preferences**. On a Mac it is in the Print dialogue under **Basic**;
- print the barcode so that its bars line up with the print head, as the guide's drawing shows;
- do not reduce or enlarge it: Brother says barcodes may not be read if they are;
- try another scanner.

For streaks or poor characters, Brother's guide says to clean the roller.

## Speed

The only speed setting in the guides is the same **Quality** option: **Give priority to print speed** or **Give priority to print quality**. For labels that carry a barcode, Brother recommends print quality.

## Gap sensing

The guides name no sensing setting and no calibration to run. What they give is how to load the roll:

- thread the DK Roll straight, so that labels are not skewed, with its edge against the upright edge of the label output slot;
- press the **Feed** button to align the end of the DK Roll.

If labels stop in the wrong place, reload the roll in that way and check Brother's three points above before looking anywhere else.

## Label size and cutting

The label size is chosen in the printer driver. Set it to the labels loaded, and turn off anything that shrinks or enlarges a page to fit.

A 4 × 6 inch label is as wide as these printers can print. Brother notes that label sides may be trimmed if the margins are too small, and that in some set-ups the full width cannot be printed. PrintStation's calibration copy shows whether yours prints the whole label.

The driver's cutting options are **Auto Cut**, which cuts each label after it is printed, and **Cut at End**, which cuts after the last label. PrintStation sends one copy at a time.

The Printer Setting Tool's **Device Settings** hold the printer's other settings, among them **Auto Cut**, **Command Mode** and the **Printer Information Report**, which prints the firmware version and the device settings. Print that report before and after a change and keep both with the qualification.

## The test: PrintStation qualification

Settings are right when the calibration copy passes. In PrintStation, an Owner opens the printer and follows [Qualify a printer and media profile](/manuals/printstation/qualification): print the calibration copy, measure between its reference marks, scan its barcode and record what came out.

| PrintStation's check | If it fails, look at |
| --- | --- |
| Each measurement within 0.5 mm of the expected value | The label size in the driver, anything that scales the page, and whether a 300 DPI profile was chosen |
| Scan the barcode into this field | Quality, set to Give priority to print quality; then the roller |
| Exactly one copy came out | The cutting option, and how the roll is loaded |
| It is upright, with TOP at the top | The page orientation in the driver |
| Nothing is clipped at any edge | The label size and margins in the driver. This is the check most at risk on a 4 × 6 inch label |
| It was not shrunk or enlarged to fit | Anything in the driver that fits the page to the label |

At Hartwell & Pryce Engineering's Brighouse works, Sarah Hughes qualifies the stores printer, a QL-1110NWB, for 4 × 6 inch labels at 300 DPI. She threads a new DK Roll straight, presses Feed, and sets the driver to the roll's label size with Quality at Give priority to print quality. In PrintStation she prints the calibration copy and measures 50.0 mm across and 50.1 mm down, against 50.04 mm expected. The barcode scans. One copy came out, upright, and she looks at each edge before ticking that nothing is clipped. Then she chooses **Record and qualify**.

Those figures describe one printer and one roll. They are not settings to copy. Enter what you measure, including a failure: do not enter the expected value because it is the target.

A qualification belongs to one workstation, one printer and one media profile. After changing the printer, its driver or the kind of roll, check it again. LabelRules also records a qualification of its own label on the same printer: see [LabelRules printer set-up](/manuals/labels/printer-setup).
