# How to cut a component to a length less a deduction

Use a starter rule to add a cut length, rounded down to the whole millimetre, and the component line that uses it.

Source: https://help.smartfact.ai/manuals/factoryspec/how-to-cut-a-component-to-a-length-less-a-deduction

Review edition: 16 November 2026

Roles: author, reviewer

Most cut parts are a dimension less a fixed allowance: a main profile cut to the finished width less 42 mm. The starter rule **Cut a component to a length less a deduction** adds a calculation for the cut length, rounded down to the whole millimetre, and a component line that uses it.

## Use the starter rule

You need the Author role, and the family needs a saved draft that the evaluator accepts, with at least one length input and one component whose Dimension profile is a length. The rule goes into the draft's next revision. No evaluation uses it until a separate Reviewer approves a release that contains it and activates it, and every result stays an evaluation result.

1. Open **Product families** and choose the family in **Open a family**.
2. Under **Starter rules**, find **Cut a component to a length less a deduction**. It is in **Calculations**, and also under **Recommended**. You can also type a word from its title in the search box above the cards.
3. Fill in the blanks in the card's sentence, "Cut … … to … less … mm, rounded down to the whole millimetre.":
   - **Count**: how many pieces each unit takes, from 1 to 9,999.
   - **Component**: one of the family's components cut to a length, shown by its description and code.
   - **Length**: the length input the cut is taken from.
   - **Deduction**: the millimetres your product expert takes off. The figure is used exactly as you enter it.
4. Choose **Use this rule**. The button waits until every blank has a value.

FactorySpec saves the draft's next revision with two new rows: a calculation at the end of **Calculations**, named "Cut length of" and the component's code, and a line at the end of **Component list** whose length is that calculation. They are the rows you would get by adding them yourself in the engineering model and choosing **Save draft**. No AI is asked. Above the cards, the page says which starter rule the revision began from.

Save or discard any unsaved change in the engineering model first: the cards wait while the editor has one. If someone saved a newer revision of the draft after you opened the page, the card is refused: reload the page, check what changed, then use the card again.

Where SmartFACT Automation is connected to FactorySpec, you can also arrive here from **New requirement** there, which offers the cards of the family whose draft changed most recently. Its **Use this rule** makes nothing: it opens Product families on that family with this card alone and its blanks filled in. Check the blanks, then choose **Use this rule** on the page. **See every starter rule** shows all the cards.

This card sets a calculation, which plain English does not describe in FactorySpec, so **Reword with AI** refuses it even where plain English is switched on.

## What the rule does

The cut length is the length less the deduction, rounded down to the whole millimetre. The rounding is recorded in the result's trace with the value before it, so the unrounded figure is kept. A unit without that length, where the length is optional, gets no line. The calculation is not shown among the result's values; the line shows the cut length.

For Frame assembly FA-300 at Brighouse works, "Cut 1 Centre support, natural finish (SUPPORT-N) to Finished external width less 42 mm, rounded down to the whole millimetre" gives a frame 1,236.7 mm wide one centre support cut at 1,194 mm, and its trace keeps 1,194.7 mm. A frame 800 mm wide gets 758 mm. The 42 mm is the product expert's figure; changing it needs review and never alters results already accepted.

## Correct the independent cases

A starter rule saves no case and changes none, because an expected component list is your product expert's to state from the engineering source: FactorySpec never works it out for you. The family's existing cases now expect a component list without the new line, so they no longer pass, and the page says the draft is not ready for independent review. Under **Independent cases** in the engineering model:

- add the new line to the expected component list of every valid case, with the cut length worked by hand from the source;
- include one case whose length less the deduction is not a whole millimetre, so the rounding is checked;
- give each change an engineering basis that names the source.

Save the draft and read the proof. Where actual and expected differ, settle it from the source, not by copying what the evaluator returns.

## Review and activate it

Choose **Run cases and request review**. The candidate freezes the model, the cases and a bounded comparison with the active release. A Reviewer who did not contribute to the model or its cases checks it and chooses **Approve this candidate**, then activates the release with a recent second factor. [Review a candidate](/manuals/factoryspec/candidate-review) describes the review. A rule from a starter rule is reviewed like any other, and an accepted result remains an evaluation result, not a manufacturing approval.

## Change it later

Nothing about a starter rule makes its rule permanent. Change the deduction in **Calculations**, the count in **Component list**, or remove both rows, and save the change as a new revision. Correct the cases, request review and activate the new release in the same way. Results already accepted keep the release and inputs they were accepted with.

## If the card is refused

A refused card saves nothing, and the message says why:

- "Not done: reload the current draft before making this change." Another author saved the draft after you opened the page.
- "Not done: this card has changed since the page was read." The draft's inputs or components, or FactorySpec's starter rule, changed. Reload the page and fill the card in again.
- "Not done: the engineering model already has this rule." A line already cuts the same component, in the same count, to the same calculation.
